2023年全國碩士研究生考試考研英語一試題真題(含答案詳解+作文范文)_第1頁
已閱讀1頁,還剩17頁未讀, 繼續免費閱讀

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、<p><b>  附錄(二)</b></p><p><b>  原文:</b></p><p>  Intelligent Control of a Novel Hydraulic Forging Manipulator</p><p><b>  Abstract</b></p&

2、gt;<p>  The increased demand for large-size forgings has led to developments and innovations of heavy-duty forging manipulators. Besides the huge carrying capacity, some robot features such as force perception, d

3、elicacy and flexibility, forging manipulators should also possess. The aim of the work is to develop a heavy-duty forging manipulator with robot features by means of combination of methods in mechanical, hydraulic, and c

4、ontrol field. In this paper, through kinematic analysis of a novel forging m</p><p>  Introduction</p><p>  The use of manipulators in open die or free forging can be traced back about 60 years

5、when development started in both Europe and the USA. Manipulators for heavy workpieces, that is, those in the region of 200 tons weight, have been developed steadily since that time, and currently there are a number of e

6、xamples of computer-controlled fully automatic forging manipulators being used . As a result of the practical use of the control system, the operators were released from mental stress, the train</p><p>  Con

7、trol of the manipulators involves rotational control in the continuous rotation and incremental angle rotation modes. The manipulator position requires integrated control with the press to achieve inches per press stroke

8、 while compensating for workpiece length increase due to cross-section area reduction of workpiece . Vitscheff demonstrates the need for compliance control when robots are used to manipulate the workpiece during forging.

9、 Specifically, the external forces exerted on the manipul</p><p>  An ASEA robot was used as an open-die forging manipulator. The ASEA robot has an inbuilt Intel microprocessor which controls its arm and gri

10、pper movements in five axes. The robot was used in conjunction with a fielding hydraulic press . The application of neural networks for compliance control of the forging robot was investigated. Effectiveness of the neura

11、l network-based compliance control module is evaluated through a full dynamic system simulation . An integrated forging plant, 25?MN open di</p><p>  The increased demand for large-size forgings has led to d

12、evelopments and innovations all around the improvement of quality and productivity. Many efforts have been undertaken to research and develop heavy-duty forging manipulators. The researches in recent years focus on the m

13、echanisms of forging manipulator, such as kinematic modeling and analysis ; dynamic load analysis, dynamic stability, and behavior ; performance analysis and optimization .</p><p>  The forging manipulator i

14、s not only an equipment with huge carrying capacity, but also a robot with delicacy and flexibility, capable of picking up and putting down workpieces gently with force perception. The compliance is another required capa

15、bility of heavy-duty forging manipulators. It is important of the promotion of quality, protection of manipulator, reduction of impact of heavy load, and energy saving. The overall aim of this work is to develop a heavy-

16、duty forging manipulator with robot</p><p>  2. Model of Control Object</p><p>  This work focuses on the novel track-mounted forging manipulator used for heavy-duty manipulations in integrated

17、open-die forging plants. This serial-parallel forging manipulator is newly designed in our institute. Its CAD model is shown in Figure 1.</p><p>  Figure1: CAD model of the serial-parallel forging

18、manipulator.</p><p>  3. Control Strategy</p><p>  The whole forging process can be divided into three stages of prepress, inpress, and afterpress. During the periods of prepress and afterpress,

19、 operations of the forging manipulator are the same: the gripper grasps the workpiece then places it on the lower die. During the period of inpress, the forging manipulator complies with the deformation of the workpiece.

20、 The control strategy of forging manipulator in these three conditions is discussed as follows.</p><p>  (a) Grasp the Workpiece</p><p>  Firstly, the horizontal and vertical position of the gri

21、pper is adjusted, and the workpiece on the bench is clamped by the gripper. Then the workpiece is lifted up by lifting cylinders with a constant lifting force which is greater than the total weight of the workpiece, grip

22、per, and its support. When the expected height is exceeded, the position error will feed back to the constant force servosystem of lifting cylinders. This negative feedback of position makes the actual lifting force smal

23、ler </p><p>  (b) Place the Workpiece</p><p>  The workpiece is fed to the forging press, right over the lower die by the forging manipulator. Then decreasing the height setting value, the balan

24、ce of force and position of lifting cylinders is broken. The actual lifting force is smaller than the total weight of the workpiece, gripper, and its support. So the workpiece moves down with the gripper. The decent velo

25、city of the workpiece is determined by the change rate of the height setting value. When the workpiece touches the lower die, the pre</p><p>  (c) Comply with the Workpiece</p><p>  During forgi

26、ng, when the workpiece is pressed by the upper die, extra force is applied on the gripper by the deformed workpiece. The force causes an increase of the load in lifting cylinders. Meanwhile, the servosystem is trying to

27、keep the lifting force constant. As a result, the gripper moves down with the workpiece and applies the minimum reaction force on the deformed workpiece. When press is over, the upper die rises, and the external force ex

28、erted on the gripper disappears. The workpiece i</p><p>  As discussed above, hybrid force/position control is the core principle in forging manipulator control. Figure 2 illustrates the hybrid con

29、trol system that incorporates these ideas. Force control is the base of the control loop. In the balanced state, expect that the actual lifting force is equal to the weight of the workpiece, gripper, and its support, sma

30、ller than the force setting value. The error of force should be compensated by another control variable. The negative feedback of error of po</p><p>  Figure 2: Construct of the hybrid control system.&l

31、t;/p><p>  Owing to the newly designed mechanism of the forging manipulator which is decoupled as discussed in Section 2, the motions of side shifting, tilting, damping, and lifting are independent, and an

32、y one of the motions has no effect on the others. The control of the forging manipulator is simplified and only related to lifting cylinders. During the whole period of forging process, front side-shifting cylinders, rea

33、r side-shifting cylinders, and tilting cylinders keep their positions all the time. Th</p><p>  4. Pressure/Position Control Method of Hydraulic Servosystem</p><p>  A block diagram of the overa

34、ll control scheme is shown in Figure3. The system is composed of controller, power amplifier, servovalve, cylinder, pressure sensor, and position sensor. </p><p>  Figure 3: Block diagram of hybrid pres

35、sure/position control system.</p><p>  Hybrid pressure/position control is very useful in manipulator lifting control where plunger cylinders are used. Based on this method, the intelligent control of forgin

36、g manipulator is realized.</p><p>  5. Analysis of Intelligent Control</p><p>  5.1. Automatic Identification of Pressure Value Settings</p><p>  As shown in Figure 4, when the

37、 workpiece is grasped by the manipulator, the hybrid pressure/position control method is used, and the pressure and position command values are set with original ones of P0 and X0. The workpiece is lifted up wi

38、th a constant force created by hybrid control loop with command pressure P0. When the position command value X0 is exceeded, the negative position error feeds back to the pressure control loop, the actual

39、pressure in system begins to decrease and will stop dec</p><p>  Figure 4: Illustration of the measurement of workpiece.</p><p>  5.2. Automatic Identification of the Placement Height of Wo

40、rkpiece</p><p>  As shown in Figure 5, supposing the workpiece is staying at a position with equilibrium of forces, decrease the command position X0 in a constant rate, then the balance has be

41、en broken. For the feedback of error of position increasing, the actual pressure will become smaller and try to go to another equilibrium state. The actual lifting force is less than the weight of the workpiece, gripper,

42、 and its support now. So the workpiece moves down until touching the lower die. At this moment, the actua</p><p>  Figure5: Illustration of the placement of workpiece. </p><p>  5.3. C

43、ompliance in Vertical Direction and Move Up Automatically</p><p>  As shown in Figure 6, when the workpiece is pressed by the upper die, the load on cylinder will increase for the deformation of workpie

44、ce; this process is called “inpress.” In the mode of pressure/position control, the increased load makes the workpiece move down, and when X < X0, the position error feed back does not work. During this

45、 period, the force acting on the workpiece by manipulator increases from weight balance pressure to the command pressure P0, while it is still much smaller than th</p><p>  Figure 6: Illustration of the

46、 compliance during forging steps.</p><p>  6. Experiment Results</p><p>  The experiments were executed on a real prototype of the novel hydraulic forging manipulator in our institute, as shown

47、in Figure 7. The mechanism and hydraulic system of the manipulator is identical with a rail-bound forging manipulator with a carrying capacity of 2000?kN and 4000?kNm load moment which is designed by our institute.

48、The main characteristics of this prototype are carrying capacity 60?kN, load moment 150?kNm, and installed power 130?kW. The hydraulic actuators are supplied by a co</p><p>  Figure 7: Prototype of the

49、novel hydraulic forging manipulator.</p><p>  Figure 8 demonstrates the measurement of the weight and the gravitational torque of workpiece. The controller attempts to maintain a constant pressure

50、4.2?MPa, and while the height of the workpiece position exceeds the preset command position 400?mm, the negative feedback of position works. When lifting cylinders stop moving, control returns to a stable steady state. T

51、he weight-balanced pressure can be identified from the curve, which is 3.55?MPa</p><p>  Figure 8: Pressure curve in lifting cylinder.</p><p>  Figure 9 depicts the process of pla

52、cing the workpiece on the lower die. While the command position signal diminished at a constant rate, the workpiece moved down trying to catch the rate. The touch of workpiece on the lower die can be detected by pressure

53、 changes in lifting cylinders. Lifting cylinders stayed on this position. The height of the workpiece placement can be found from the curve.</p><p>  Figure 9: Position curve in lifting cylinder.</p&

54、gt;<p>  The experiment results show that the technique is straightforward and feasible. All the supposed control methods have been realized on the prototype of the forging manipulator. The experimental datum form

55、s the base of further </p><p>  research on intelligent control of heavy-duty forging manipulators.</p><p>  7. Conclusions</p><p>  A novel hydraulic forging manipulator is propose

56、d, with newly designed mechanism, intelligent control strategy, and improved hydraulic control method. The major motion mechanism is decoupled, thus the control of the forging manipulator is greatly simplified. Workpiece

57、s can be picked up and put down gently by forging manipulators with force perception. Moreover, the forging manipulator can comply with the external forces exerted on it by workpiece during forging steps. These are based

58、 on a new pr</p><p>  References </p><p>  E. Appleton, W. B. Heginbotham, and D. Law, “Open die forging with industrial robots.,”Industrial Robot, vol. 6, no. 4, pp. 191–194, 1979. View a

59、t Scopus</p><p>  “Attaining practicality of freely programmable control of an open die forging press and forging manipulator by a computer,” Ishikawajima-Harima Engineering Review, vol. 17, no. 6, pp.

60、599–606, 1997.</p><p>  R. A. Ridgeway, “Microprocessor utilization in hydraulic open-die forge press control,” IEEE Transactions on Industrial Electronics and Control Instrumentation, vol. 22, no. 3, p

61、p. 307–309, 1975. View at Scopus</p><p>  V. Vitscheff, “A programmable manipulator for closed die forging,” in Proceedings of the 9th International Drop Forging Convention, Kyoto, Japan, 1977.<

62、/p><p>  W. B. Heginbotham, A. K. Sengupta, and E. Appleton, “An ASEA robot as an open-die forging manipulator,” in Proceedings of the Second IFAC/IFIP Symposium, pp. 183–193, Stuttgart, Germany, 1979.<

63、/p><p>  A. K. Sengupta, E. Appleton, and W. B. Heginbotham, “Ring forging with an industrial robot,” inProceedings of the 10th International Symposium on Industrial Robots, pp. 29–42, Milan, Italy, 1980.</p

64、><p>  K. W. Lilly and A. S. Melligeri, “Dynamic simulation and neural network compliance control of an intelligent forging center,” Journal of Intelligent and Robotic Systems, vol. 17, no. 1, pp. 81–99, 1

65、996. View at Scopus</p><p>  A. S. Melligeri and K. W. Lilly, “Application of neural networks in compliance control of an integrated robot/forge processing center,” in Advances in Manufacturing Sys

66、tems: Design, Modeling and Analysis, pp. 445–450, Elsevier, New York, NY, USA, 1993.</p><p>  M. Baldassi, “Open die forging presses with manipulators,” Forging, vol. 14, no. 5, pp. 16–18, 2003.</p&g

67、t;<p><b>  譯文:</b></p><p>  一種新型的液壓鍛造操作機的智能控制</p><p><b>  摘要</b></p><p>  大尺寸鍛件的需求增加,導致重型鍛造機械手的發展和創新。重型鍛造機械手除了具有巨大的承載能力,還應該具備一些機器人的感知力、精致和靈活性的功能。工作的目的

68、是通過液壓和控制領域相結合的方法來通過機械手開發一種重型鍛壓機械以實現機器人功能。在本文中,通過一種新型的鍛造操作機的運動學分析和控制策略的實現,實現鍛造機械手預定的功能和運動。且實現鍛造操作機的液壓執行器的混合壓力/位置控制。該控制方法的可行性已由我們研究所的一個真正新型液壓鍛造操作機的實驗原型證實。鍛造操作的智能控制與可編程邏輯控制器適用于工業應用。</p><p><b>  1.介紹</b

69、></p><p>  開?;蜃杂慑懺鞕C械手的使用可以追溯到大約60年的時候就開始在歐洲和美國發展。也就是說,自那時起,該區域的200噸較重的工件的機械手的已穩步發展,目前有一些實施例,即所使用計算機控制的全自動鍛造機械手。作為控制系統的實際使用結果,可使經營者被釋放精神壓力,減少操作員的訓練期,鍛件質量的均勻性被提高,且達到更高的生產速率。</p><p>  操縱控制涉及在旋轉控

70、制中的不斷旋轉和增量角度旋轉模式。對于機械手的位置,要求集成控制實現按壓力控制,同時補償工件由于截面積減少而長度增加。 vitscheff[4]表明,有必要時,機器人被用來操縱在鍛造過程中的工件合格。具體而言,是通過在鍛造工序的工件操縱器上施加外力,且必須是最小化,以避免損壞的機器人機構。</p><p>  ASEA機器人被用來作為一個開放式模鍛操作。 ASEA機器人有一個內置的英特爾微處理器,用五根軸控制其手

71、臂和抓手運動。機器人應用在相應的液壓機中。類神經網路合規控制的鍛造機器人的應用已在研究?;谏窠?jīng)網絡的合規控制模塊的有效性是通過一個完整的動態系統仿真評估。一個綜合鍛件廠,始建于1999年25 MN開模壓力機200kN和400KNM機器人。將工件放入預定位置,以旋轉和行程運動閉式液壓回路驅動,以減少能源消耗和沖擊,且操縱者由綁定的兩個軌道以提高定位。軌道結合的鍛造操作機帶載能力為1600千牛,4000KNM負載力矩在JSW 2007年開

72、始運作。操縱器支持直線運動,比如因為特殊的杠桿安排的剝離而精確和穩定的定位 。</p><p>  大尺寸鍛件的需求增加,導致了各地的改進質量和生產力的發展、創新。對研究和開發重型鍛造機械手已經進行了許多努力。近年來的研究專注于鍛造操作機的機制,如運動建模和分析;動態負載分析、動態穩定性和動作;性能分析和優化。</p><p>  鍛造操作機不僅是一個巨大的承載能力的設備,但也是一個微妙性

73、和靈活性,能夠拿起和放下工件并輕輕感知力的機器人。合規性是重型鍛造機械手需要的另一個能力。提高質量,減少重負載的影響,保護操作者并能節能是很重要的。這項工作的總體目標是通過機械手和機器人功能而開發一的種液壓和控制領域相結合的重型鍛壓機械。一種新型鍛造操作機的運動學分析正在實現。在此基礎上,操作者的控制策略建議考慮鍛造機械手的功能和作用。鍛造操作機的液壓執行器的混合壓力/位置控制已經實現。在我們研究所控制新型液壓鍛造操作機真實模型以達到智

74、能控制的目標。</p><p><b>  2.控制對象模型</b></p><p>  今年工作重點放在另一個開放式模鍛廠重型操作的新型軌道式鍛造機械手。這系列并聯鍛造操作機是我們研究所的新設計。CAD模型如圖1中所示。</p><p>  圖1:一系列鍛造操作并行CAD模型。</p><p><b>  3

75、.控制策略</b></p><p>  整個鍛造過程可分為press,inpress,afterpress三個階段。在press和afterpress期間內,鍛造操作機操作是相同的即抓住工件然后把它放在下模抓手。在鍛造操作inpress期間,符合工件的變形。這三個條件的鍛造操作機的控制策略討論如下。</p><p><b> ?。╝)抓住工件</b><

76、;/p><p>  首先,調整夾持器的水平和垂直位置,由夾持器在長凳上夾緊工件。然后,工件被夾持器和升降氣缸以大于工件總重量的恒定提升力抬起。當超出預期高度,位置誤差反饋恒力給起重缸伺服系統。這種負反饋的位置使實際提升力小于設定值。在均衡狀態下,實際的提升力等于工件的總重量,夾持器和支持力的誤差等于乘以一個系數的位置的誤差。</p><p><b>  (b)放置工件</b&g

77、t;</p><p>  工件被輸送到鍛壓機的壓力下,在下模鍛造操作。然后降低高度設定值,起升油缸力和位置的平衡被打破了。夾持器的支持實際提升力小于工件的總重量計。所以工件向下移動機械臂。工件合宜的速度由高度設定值的變化率決定。當工件接觸到下模,升降氣缸會發生很大變化,工件開始得到下模具中的壓力。在這一刻,保持高度設定值不變,那么起升油缸力和位置涉及到一個新的平衡。</p><p><

78、;b>  (c)回應工件</b></p><p>  在鍛造過程中,當工件由上模壓制,額外的力由變形工件施加在夾持器,力使舉升油缸的負載的增加。同時,該伺服系統試圖保持提升力常數。作為一個結果,手爪與工件向下移動,將最小反應力對工件變形。當按下結束后,上模上升,而施加在夾持器外力消失。工件由一個恒定的提升力被抬到原來的位置。然后,機械手進給搬運工件。接下來壓力準備。</p><

79、;p>  如上所述,力/位置混合控制是鍛造機械手控制的核心原則。圖2這些想法說明了混合控制系統。力控制是控制回路的基礎。在平衡狀態,預計實際升力等于工件、夾具的重量和它的支持,小于力設定值。力的錯誤應該被另一個控制變量的補償,且位置誤差的負反饋將被添加到控制回路。當實際升降位置低于設定值的高度,位置誤差的反饋是零,爪在持續力下不斷提升。當實際升降位置高度高于設定值的位置誤差,系統開始負反饋,而實際升力減小直至力和位置趨于平衡。&l

80、t;/p><p>  圖2:混合動力控制系統的構建</p><p>  新設計的鍛造操作機的機身部分,運動的側移、傾斜、阻尼和提升是獨立的,且運動的任何一個對其他部分沒有影響。鍛造操作機的控制被簡化只與升降缸有關。在鍛造過程的整個期間,總是保持前側移缸,后側移位和傾斜缸。在水平方向上的工件的變形是由阻尼缸在inpress中吸收。合規時發生的變形阻力大于設定值的卸壓閥阻尼回路。取決于對減壓閥性能

81、的水平方向上的作用力,幾乎保持不變。</p><p>  4.液壓伺服系統的壓力/位置控制方法</p><p>  整體控制方案的框圖如圖3所示。該系統由控制器、功率放大器、伺服閥、氣缸、壓力傳感器、位置傳感器組成。</p><p>  圖3:混合壓力/位置控制系統框圖</p><p>  當柱塞缸采用時,混合壓力/位置控制是非常有用的機械臂

82、升降控制?;谶@種方法,實現了對鍛造操作機的智能控制。</p><p><b>  5.智能控制分析</b></p><p>  5.1 壓力值設置的自動識別</p><p>  如圖4,當工件被把持通過操作器,使用混合動力壓力/位置控制方法,設定的壓力和位置命令值P0 和 X0的原始值。工件被一個恒定的壓力P0力升起,且位置的命令值X0超標,

83、負位置誤差反饋到壓力控制回路,系統中的實際壓力開始減少,減少的重量直到平衡為止。在均衡狀態下,工件停止移動,實際提升力等于工件的總重量、夾持器和支持力。記錄這個實際的平衡壓力,并用它在鍛造過程中的合規控制壓力設定值。</p><p>  圖4:測量工件的插圖</p><p>  5.2 自動識別放置工件高度</p><p>  如圖5所示,假設工件停留在一個與力量平

84、衡的位置,減少命令行的位置X0和恒定的速率,然后平衡將會被打破。對于反饋的錯誤增加,實際壓力將變得更小,并嘗試去到另一個平衡狀態。實際提升力小于工件的重量、夾持器和支持力。因此,工件向下移動,直到碰到下模。在這個時刻,實際的壓力迅速下降。根據壓力的變化率,能夠自動識別工件的放置狀態。保持命令工件位置X0并放置在下模高度值。起升油缸的壓力和位置進入到一個新的平衡。</p><p>  圖5:插圖工件的位置</

85、p><p>  5.3 在垂直方向上的合規性和自動上移</p><p>  在圖6所示,當工件被上模按下時,在氣缸上的負載會增加工件的變形,這個過程被稱為“inpress?!币詨毫?位置控制模式,增加的負載使工件向下移動,當X<X0,位置誤差反饋不工作。在此期間,力作用在工件上的機械臂從重量平衡壓力命令壓力P0增加,而它仍然是遠遠小于壓力。因此,實現在垂直方向上的匹配。印刷機完成時,上模

86、向上移動,這個過程叫做“afterpress,”缸上的負載減少。提升力使工件升降缸的壓力和位置向上移動,直到進入到一個新的平衡。</p><p>  圖6:符合鍛造工序插圖</p><p><b>  6.實驗結果</b></p><p>  實驗是我們研究所的一個新型液壓鍛造操作機的原型,如圖7所示。我院設計的機械和液壓系統的操盤與??導軌結

87、合的帶載能力為2000KN,4000KNM負載力矩。這個原型的主要特點是承載能力60KN,負載力矩150KNM,裝機功率130KW。液壓致動器所提供的恒定壓力的泵源由servoproportional位置換能器的閥控制??删幊踢壿嬁刂破鲌?zhí)行所有的控制操作。</p><p>  圖7:原型的新型液壓鍛造操作機</p><p>  圖8演示了測量工件的重量和重力轉矩??刂破髟噲D保持一個恒定的4

88、.2兆帕壓力,而工件位置的高度超過預設的命令位置400毫米,負反饋的位置是正常的。當起升油缸停止移動,控制返回到穩定狀態。可以從曲線上確定的,這是3.55兆帕的重量平衡的壓力。</p><p>  圖8:舉升缸壓力曲線</p><p>  圖9描述出工件上的下模過程。雖然命令位置信號以恒定的速率減少,工件向下移動試圖捕捉速率。在升降缸中下模具工件上的觸摸可以檢測到壓力的變化。起升油缸留在這

89、個位置。從曲線中可以發現工件放置的高度。</p><p>  圖9:舉升缸位置曲線</p><p>  實驗結果表明,該技術是簡單的和可行的。所有所謂的控制方法已經實現了鍛造操作的原型。實驗數據為重型鍛造機械手智能控制研究形成了基礎。</p><p><b>  7.結論</b></p><p>  新設計的機制和智能控

90、制策略,以及改進的液壓控制方法,提出了一種新型的液壓鍛造操作方法。主要機制的解耦,從而大大簡化了鍛造操作的控制。工件可以被鍛造機械手拿起和輕輕放下。此外,鍛壓機械手可以在鍛造工序中施加于工件合適的力。這些都是基于一個新的壓力控制方法和本文提出的液壓伺服系統的混合動力車壓力/位置控制方法。所有液壓控制方法和智能控制策略已核實,并通過實驗原型鍛造操作。這項工作為智能重型鍛造機械手的進一步發展提供了理論和實踐基礎。</p>&l

91、t;p><b>  參考文獻</b></p><p>  1. E. Appleton, W. B. Heginbotham, and D. Law, “Open die forging with industrial robots.,”Industrial Robot, vol. 6, no. 4, pp. 191–194, 1979. View at Scopus<

92、/p><p>  2. “Attaining practicality of freely programmable control of an open die forging press and forging manipulator by a computer,” Ishikawajima-Harima Engineering Review, vol. 17, no. 6, pp. 599–606,

93、1997.</p><p>  3. R. A. Ridgeway, “Microprocessor utilization in hydraulic open-die forge press control,” IEEE Transactions on Industrial Electronics and Control Instrumentation, vol. 22, no. 3, pp. 307

94、–309, 1975. View at Scopus</p><p>  4. V. Vitscheff, “A programmable manipulator for closed die forging,” in Proceedings of the 9th International Drop Forging Convention, Kyoto, Japan, 1977.</p

95、><p>  W. B. Heginbotham, A. K. Sengupta, and E. Appleton, “An ASEA robot as an open-die forging manipulator,” in Proceedings of the Second IFAC/IFIP Symposium, pp. 183–193, Stuttgart, Germany, 1979.</p

96、><p>  A. K. Sengupta, E. Appleton, and W. B. Heginbotham, “Ring forging with an industrial robot,” inProceedings of the 10th International Symposium on Industrial Robots, pp. 29–42, Milan, Italy, 1980.</p&g

97、t;<p>  7. K. W. Lilly and A. S. Melligeri, “Dynamic simulation and neural network compliance control of an intelligent forging center,” Journal of Intelligent and Robotic Systems, vol. 17, no. 1, pp. 81–99,

98、 1996. View at Scopus</p><p>  A. S. Melligeri and K. W. Lilly, “Application of neural networks in compliance control of an integrated robot/forge processing center,” in Advances in Manufacturing S

99、ystems: Design, Modeling and Analysis, pp. 445–450, Elsevier, New York, NY, USA, 1993.</p><p>  M. Baldassi, “Open die forging presses with manipulators,” Forging, vol. 14, no. 5, pp. 16–18, 2003.</p

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 眾賞文庫僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

評論

0/150

提交評論