外文翻譯--movax說明手冊

1、<p>　　附錄三 英文資料翻譯及原文</p><p><b>　　Movax說明手冊</b></p><p><b>　　目錄 </b></p><p>　　SP 20 - SPH80</p><p><b>　　中文</b></p><p&g

2、t;<b>　　V 100603 </b></p><p><b>　　1. 簡介</b></p><p>　　2. 液壓系統及功能</p><p>　　3. 安全指示和保修事項</p><p>　　4. 操作前的基本檢查16</p><p>　　5. 提伸樁至垂直位

3、置</p><p><b>　　6. 搬運樁</b></p><p>　　7. 挖掘機斗桿力</p><p>　　8. 液壓系統空氣的凈化</p><p>　　9. Movax和Movax II 的自動操控</p><p><b>　　10. 手動打樁</b>&

4、lt;/p><p><b>　　10. 手動打樁</b></p><p>　　11. 實踐訓練錯誤!未定義書簽。</p><p>　　12. 保修注意事項</p><p><b>　　13. 可選零件</b></p><p>　　14. 實用性建議</p>

5、<p>　　15. SPH80型號中“錘擊樁”命令的修改的介紹＝改變相位錯誤!未定義書簽。</p><p>　　16. Movax SP W/SPH W型號的特別提示</p><p>　　下夾樁爪液壓缸墊片 附錄1

6、 </p><p>　　Movax/挖掘機適配器 附錄2</p><p><b>　　1.簡介</b></p><p>　　獨特性在于它的側面性，

7、側面工作允許在其他同類產品無法工作的地方工作（如隧道、橋底下、動力線下與那些超過規定高度的地方）。使用Movax裝置搬運一根12米長的樁甚至只須一臺普通的挖掘機 </p><p>　　認真閱讀這本手冊, ,了解使用Movax什么是允許和安全的. 本手冊中您也可以從其他使用者的經驗中找到有用的提示</p><p>　　隨著對Movax的不斷地研究和改進，它的性能提高了很多并將有更多的改進&l

8、t;/p><p>　　在訂購Movax的備件時請清楚序列號、類型和所有可能做了的變化. 這些確保你將獲得正確的零配件。自動裝置的一些地方都有自己的系列號和版本號， 當訂購零件時，你也應該注意到。</p><p>　　為了安全的最大性能的發揮Movax的優勢，請注意指南中所有安全預防措施</p><p>　　通過培訓，操作證書作為一個單獨的證明授予操作者。 </p&

9、gt;<p><b>　　1.1 運輸過程</b></p><p>　　把電纜線B從顯示器上拔出，因?yàn)樵谶\(yùn)輸過程中，假如挖掘機接觸電源線， 駕駛室的電腦有可能被燒毀。</p><p>　　1.2在挖掘機/Movax/樁上焊接時</p><p>　　焊接之前，關閉電腦和把電纜線B從監視器上拔出</p>&l

10、t;p><b>　　1.3連接器的保護</b></p><p>　　拔出電纜后，保持連接器的清潔和防止顯示器的電源線短路</p><p>　　在拔出電纜前先關閉顯示器</p><p>　　當拔出電纜，保護好液壓系統連接器及軟管，防止污垢進入液壓系統</p><p>　　2. 液壓系統功能介紹</p>

11、<p><b>　　2.1 鉗</b></p><p><b>　　每個鉗口同時動作</b></p><p>　　振動時停止鉗爪的動作</p><p>　　在使用第四個鉗爪時，請?zhí)貏e注意，它張開時其他的鉗爪是停止的。</p><p>　　注意：當用第四個鉗爪打樁時，只需要一個按鈕<

12、/p><p><b>　　2.2 傾斜油缸</b></p><p><b>　　傾斜角度±30度</b></p><p>　　當振動打樁時總是開啟“傾斜浮動”，選自動檔二檔時將自動開啟，在樁被打入0.5米時，軟件版本2.86或更后的版本會自動開啟“傾斜浮動”</p><p><b>

13、　　2.3 振動馬達</b></p><p>　　SP20-60大約3000RPM（取決于挖掘機油的流動性）</p><p>　　SPH80大約4000RPM</p><p>　　需要的油液流動性取決于Movax型號，不要超過標準值（參考表3，第21頁）</p><p>　　注意：SPH80也有一條泄油管，為了保護馬達，它應該最先

14、連接和最后斷開。</p><p>　　小心！SPH80型的油液流動速度最大是240升每分鐘。超過最大流量授權將是無效的。</p><p><b>　　2.4 回轉馬達</b></p><p>　　利用渦輪轉動，由于采用旋轉接頭，所以它的旋轉角度是無限的</p><p>　　2.5 鎖定油缸（只有SP40-60 配備）&l

15、t;/p><p>　　當提升長重樁時使用（超過8米）</p><p>　　使用鎖定油缸后，Movax成為U形架和吸收橡膠塊，不能負擔樁的重量。鎖定油缸連接振動馬達和U形架。</p><p>　　當樁位于垂直位置時，松開鎖定油缸。</p><p>　　當使用振動時，液壓系統會自動松開鎖定油缸，但是有可能不松開，如果你牢牢按住前臂，在振動前，系統將不

16、停核實鎖定油缸是否已經打開。</p><p>　　在抓一根超過8米長的樁前，記得確保鎖定油缸鎖定，鎖定油缸是人工操作（見第5章）。</p><p>　　在沒有鎖定鎖定油缸提升超過8米的樁時，保修服務將失效。</p><p>　　SPH80沒有鎖定油缸，但配置更多的吸收橡膠，樁的安全重量為1000千克</p><p>　　注意：如果移動U形架上

17、的4/2閥（清洗時），確保用同樣的方式把它們安裝在同樣的地方，如果你打開控制鉗爪和鎖定油缸的閥，請注意閥上線軸的尾端指向旋轉接頭，否則架子所將不會打開和鉗爪將不會鎖定在振動時。</p><p>　　2.6 0度以下啟動Movax</p><p>　　液壓油在冷時是稠的（有很大的回路壓力）</p><p>　　當溫度“冰凍”時，不要振動，否則將損壞液壓馬達及軸密封&

18、lt;/p><p>　　根據挖掘機的指示把油液熱起來，當油溫達到20度時，低RPM運行振動（無樁）。振動3-5分鐘，加熱Movax液壓系統的油液</p><p>　　3 安全指示和保修條件</p><p>　　3.1操作人員的安全指示</p><p>　　由下面的例子可以知道，Movax SP 模型能用不能的方式提升和轉移樁</p>

19、<p><b>　　從地板上提升樁</b></p><p>　　提升可能利用側握,下握,部分薄板樁使用第四鉗爪.</p><p>　　3.1.1尾爪（第三爪）</p><p>　　在尾爪離開樁的根部之前，樁必須被牢固固定在地面上。</p><p>　　圖1

20、 圖 2</p><p>　　換爪前樁必須固定在地面</p><p>　　如果有樁滑動或下落，不要張開爪。</p><p>　　3.1.2 第四個鉗爪提升樁（見圖3）</p><p>　　A）確保無其他人在工作區域。</p><p>　　B）提升樁最多離地0.5米，避免樁撞擊其他東西。強烈的撞

21、擊將會損壞第四鉗爪的螺栓和使樁墜落。</p><p>　　圖3 使用第四爪提升樁 圖4 使用側爪夾樁 </p><p>　　3.1.3側爪——樁在其中</p><p>　　A）確保無其他人在工作區域</p><p>　　B）夾樁的中部，然后按?。P(guān)閉爪）按鈕2-3秒以確保已經牢固夾住樁。</p&g

22、t;<p>　　C）不要用樁猛烈撞擊其他東西</p><p>　　3.1.4 側爪——從樁的側面夾樁（見圖5）</p><p>　　注意以下安全防范:沒有安全鏈時絕不要夾樁的側面</p><p>　　圖5 不安全的提升樁的方式 圖6 不正確的夾樁方式</p><p><b>　　3.

23、2特殊保修條件</b></p><p>　　1. Movax操作者必須有資格證書. (更多見第1，10，11章)</p><p>　　2. 開始提升的過程中,必須依照指示進行操作. (更多見第2.6章)</p><p>　　3. Movax應經常使用正確的振動RPM和工作壓力(更多見章節4.3 4.4表和第22頁) .</p><p

24、>　　4 . 軸承溫度不能超過90 - 100℃</p><p>　　5. 振動馬達內液壓油的數量和質量必須是正確的(具體見章12.1 )</p><p>　　6 . 首次換液壓油時間不超過20個小時.</p><p>　　4．操作前的基本檢查</p><p><b>　　4．1檢查油位</b></p>

25、<p>　　檢查壓樁機的油位使用角度傳感器（壓樁機的X=0，壓樁機的Y=0）</p><p>　　油位必須是在是視油玻璃孔從底部數起的第一個四分之一刻度線到底部之間（看圖8）。用油量超過標準，會導致壓樁機使用性能降低。</p><p>　　圖8油位太高，可能導致溫度過高</p><p>　　SPH80型號的油面觀察玻璃的位置見于24頁。</p&g

26、t;<p>　　4.2檢查裂縫和泄漏</p><p>　　確保完成了維修服務。（換油，潤滑）</p><p>　　檢查軟管處是否有泄漏或損壞的地方。</p><p>　　檢查抓鏟的墊子。必須有超過50%的齒空余（見12章4節）。</p><p>　　仔細檢查所有的焊縫/鐵板是否有裂縫。</p><p>　

27、　所有的破損都必須在壓樁機使用前修復。</p><p>　　檢查并加緊松了的螺釘和水壓裝置。</p><p>　　注意！要認真保持螺釘和水壓裝置的清潔，在加緊螺釘之前請使用密封膠。</p><p>　　檢查電線（電纜）和其它聯接裝置是否有損壞。</p><p>　　視察外面的吸附橡膠層。</p><p>　　4.3檢查

28、油箱輸油線路</p><p>　　確保壓力的調整和油缸軟管（在SPH80型號里包括溢流線路）相互之間都處于合適的狀態。如果分離裝置的鉆孔機油路是開或關的狀態或者有分流，必須保證：油箱的輸油管路是打開的！在油箱輸油管路關閉的狀態下使用壓樁機或?qū)е滤畨合到y(tǒng)的嚴重受損尤其是馬達部分。</p><p>　　當水壓系統替換軟管或者進行了其它可能導致空氣進入系統的動作之后，一定要把空氣抽盡。只要振蕩1

29、0-15秒即可實現。注意！振蕩不能消除柱閥和旋轉管里面的空氣（見第8章）。在夾緊樁之前仔細檢查每個動作。</p><p>　　4.4檢查鉆孔機的油的流量和油壓。</p><p>　　每工作750-1000個小時檢查一次油量和油壓.(詳見22頁)</p><p>　　當行使到地質較軟的地方時，選用鉆孔機發動機的低轉速，但要保證壓樁機的振動馬達時刻在平穩地運行。（不要引

30、起振動馬達的共振）</p><p>　　當行駛到地質較硬的路面上時，使用高轉速以便加大油的流量。同時也要保證振動馬達運行的平穩性。不過，也不能使壓樁機馬達每分鐘的轉速過高。</p><p>　　注意: 低于30％的油流量可以導致劇烈的共振，從而引發：</p><p><b>　?。?使軸承升溫</b></p><p>&

31、lt;b>　?。?軸承損壞</b></p><p><b>　　－ 振桿斷裂</b></p><p>　　5.打樁時角度要垂直</p><p>　　在用夾樁鏟夾緊樁之前，檢查樁與壓樁機是否平行（見圖9）。</p><p>　　在舉樁之前，確保夾樁鏟卡在樁的內側（見圖10）。</p><

32、;p>　　按下“夾緊”按鈕并持續2-3秒，使夾樁鏟提供了最大的工作輸出。</p><p>　　使樁稍微提離地面。（見圖11）</p><p>　　圖9樁與夾樁鏟平行 圖10夾在樁內側 圖11稍微提離地面</p><p>　　MOVAX INSTRUCTION MANUAL</p><p>　

33、　TABLE OF CONTENTS</p><p>　　SP 20 - SPH80</p><p><b>　　English</b></p><p><b>　　V 100603 </b></p><p>　　1. INTRODUCTION10</p><p>　　2.

34、 HYDRAULIC SYSTEM AND FUNCTION12</p><p>　　3. SAFETY INSTRUCTIONS AND WARRANTY CONDITIONS4</p><p>　　4. BASIC INSPECTION BEFORE OPERATION16</p><p>　　5. LIFTING A PILE INTO VERTICAL

35、 POSITION18</p><p>　　6. DRIVING – EXTRACTING THE PILE錯誤!未定義書簽。</p><p>　　7. EXCAVATOR BOOM FORCE錯誤!未定義書簽。</p><p>　　8. PURGING AIR FROM THE HYDRAULIC SYSTEM錯誤!未定義書簽。</p>&l

36、t;p>　　9. MOVAX AUTOSTEERING AND MOVAX II AUTOSTEERINGMovax和錯誤!未定義書簽。</p><p>　　10. PILING WITHOUT AUTOMATICS錯誤!未定義書簽。</p><p>　　10. PILING WITHOUT AUTOMATICS錯誤!未定義書簽。</p><p>　

37、　11. PRACTICAL TRAINING錯誤!未定義書簽。</p><p>　　12. MAINTENANCE INSTRUCTIONS錯誤!未定義書簽。</p><p>　　13. OPTIONAL EQUIPMENT錯誤!未定義書簽。</p><p>　　14. PRACTICAL ADVICE錯誤!未定義書簽。</p><p&

38、gt;　　15. INSTRUCTIONS TO CHANGE THE “HITTING” DIRECTION OF SPH80 </p><p>　　= CHANGING THE PHASE錯誤!未定義書簽。</p><p>　　16. MOVAX SP W / SPH W SPECIAL INSTRUCTIONS:錯誤!未定義書簽。</p><p>　　LO

39、WER CYLINDER SHIMMINGappendix 1</p><p>　　MOVAX / EXCAVATOR ADAPTERappendix 2</p><p>　　1. INTRODUCTION</p><p>　　Movax sheet-piler is unique because of its side-grip. The side-grip

40、 allows you to work in places( tunnels, under bridges, under power-lines, and generally wherever the space above the pile is limited) where other competitors can’t. By using Movax you can drive even 12 meter long piles

41、with normal excavator.</p><p>　　Read this instruction manual conscientiously with thought, to understand what is allowed and safe when using Movax. In this manual you will also find useful hints from other

42、users.</p><p>　　Because of the constant research and development performed on Movax, it has been changing during the years and will continue to change in the future.</p><p>　　When ordering spare

43、 parts for Movax always make sure to inform the serial number, type and all the possible changes that have been done on your Movax. This insures you will receive the correct spare parts. Some parts on the automatics ha

44、ve their own serial-numbers and version-numbers. You should also note them when ordering parts for it.</p><p>　　To safely get the maximum benefit from your Movax, please pay attention to all safety precauti

45、ons mentioned in this manual.</p><p>　　The operator’s certificate is a separate document given to an operator after the training.</p><p>　　1.1 During transportation</p><p>　　Disconn

46、ect the cable B from the display because the computer inside the cab might get damaged if the excavator touches power lines during the transportation</p><p>　　1.2 When welding excavator / Movax or the pile&l

47、t;/p><p>　　Turn off the computer and disconnect the cable B from the monitor before welding</p><p>　　1.3 Protecting connectors</p><p>　　After disconnecting, protect the connector from

48、impurities and see that the power line of the display does not short circuit</p><p>　　The display has to be turned off before disconnecting cables </p><p>　　Protect all hydraulic connectors and

49、hoses while they are disconnected so that dirt cannot enter the hydraulic system</p><p>　　2. HYDRAULIC SYSTEM AND FUNCTION</p><p><b>　　2.1 Jaws</b></p><p>　　All jaws m

50、ove at the same time</p><p>　　Close during the vibration</p><p>　　When using the 4th jaw, pay special attention because it opens when other jaws close</p><p>　　Caution: Only one

51、button is needed to drop a pile from the 4th jaw</p><p>　　2.2 Tilt cylinder</p><p>　　Tilting angle 30</p><p>　　Always use tilt floating while vibrating. Driving automatically with

52、Auto II, software version 2.86 or later one will automatically activate tilt floating after the pile has been driven 0,5 meters down.</p><p>　　2.3 Vibra-motor</p><p>　　SP 20 - 60 about 3000 RPM

53、(depending on the oil flow of the excavator)</p><p>　　SPH 80 about 4000 RPM</p><p>　　Needed oil flow depends on Movax Model. Do not exceed oil flow (see table 3, page 21).</p><p>　

54、　NOTE: SPH 80 also has a leak line and it should be connected first and disconnected last to protect motors</p><p>　　CAUTION! The max oil flow of the SPH 80 is 240 l/min. Exceeding the max oil flow voids t

55、he warranty.</p><p>　　2.4 Swing motor</p><p>　　Uses worm gear to rotate Movax. Due to rotary joint, the rotation angle is unlimited</p><p>　　2.5 Lock cylinder (ONLY SP 40 – 60) &l

56、t;/p><p>　　Use when lifting long heavy piles ( over 8m ) </p><p>　　With the lock cylinder, the Movax becomes one with the U-frame and the absorbing rubbers are no longer carrying all the weight of

57、the pile. Lock cylinder connects the vibrating part to the U- frame</p><p>　　Disengage the lock cylinder, when the pile is in vertical position </p><p>　　The hydraulic system disengages the loc

58、k cylinder automatically when vibrating, However, it might not open, if you press Movax firmly with the boom. Always verify that the lock (see pictures 14,15) is disengaged before vibrating.</p><p>　　Rememb

59、er to engage the lock before gripping onto a pile longer than 8m. The locking is always to be done manually (see chapter 5).</p><p>　　The warranty will lapse, if piles longer than 8m, are lifted without lock

60、ing the lock cylinder</p><p>　　SPH 80 does not have a lock cylinder, but includes more absorbing rubbers. Safe pile weight is 1000 kg</p><p>　　NOTE! If you remove the 4/2 valves above U-frames

61、 (for cleaning), be sure to refit them on same places and in same way as they were. If you open the valves which control the jaws and the lock cylinder, note that the grinded ends of the spools of the valves must point t

62、owards the rotary joint. Otherwise the frame lock does not open and jaws are not locked during the vibration.</p><p>　　2.6 Starting Movax when the temperature is below 0C</p><p>　　Note that the

63、oil is thick when cold (very high return pressure)</p><p>　　Never vibrate when the oil temperature is “freezing”, because it will damage the hydraulic motors and shaft-seals.</p><p>　　Heat up th

64、e hydraulic oil following the excavator's manufacturer instructions. When the oil temperature is about 20C, start vibrating with low RPM's (without pile). Vibrate for 3 – 5 minutes to warm up the oil in Movax a

65、nd the hydraulic system</p><p>　　3.SAFETY INSTRUCTIONS AND WARRANTY CONDITIONS</p><p>　　3.1. Safety instructions for operator</p><p>　　Movax SP models can lift and transfer the pile

66、 in different ways, as explained below.</p><p>　　Lifting a pile from the ground.</p><p>　　The lifting is possible using the side grip, end grip, and with some sheet pilers using the 4th jaw.<

67、/p><p>　　3.1.1 End grip (3rd jaw)</p><p>　　The pile must be firmly on ground before taking a grip from the end of the pile. </p><p>　　Picture 1. Picture 2.</p>

68、<p>　　The pile must be firmly on ground before changing the grip.</p><p>　　Do not open the jaws, if there is a danger of pile slipping or falling.</p><p>　　3.1.2 Lifting with the 4th jaw

69、(see picture 3) </p><p>　　A) Check that NOBODY is in the working area. </p><p>　　B) Lift the pile max 0.5m from the ground, avoid hitting the pile against </p><p>　　anything. Stro

70、ng hit will break the 4th jaw bolts and cause the pile to drop.</p><p>　　Picture 3 Lifting with 4th jaw Picture 4 Handling a pile using the side-grip</p><p>　　3.1.3 Side-grip – inside the

71、 pile (see picture 4) </p><p>　　A) Check that nobody is in the working area </p><p>　　B) Take grip inside the pile in the middle and press “close jaws” button for 2-3 seconds to ensure that you

72、have a firm grip of the pile.</p><p><b>　　mm</b></p><p>　　C) Don’t hit the pile against anything.</p><p>　　3.1.4 Side-grip – from the side of the pile (see picture 5)&l

73、t;/p><p>　　Note the following safety precaution:</p><p>　　Never lift a pile without a safety chain when gripping it from the side.</p><p>　　Picture 5 Unsafe way to lift a pile Pict

74、ure 6 Incorrect way to grip a pile</p><p>　　3.2 Special Warranty Conditions </p><p>　　1.Every Movax operator must have operator’s certificate. </p><p>　　(See more on chapters 1, 1

75、0 and 11)</p><p>　　2. Start up –procedure must be carried out according to the instructions. </p><p>　　(See more on chapter 2.6.)</p><p>　　3. Movax should always be used at correct

76、vibration RPM and working pressure</p><p>　　(See more on chapters 4.3, 4.4 and table on page 22.)</p><p>　　4. BEARING TEMPERATURE SHOULD N EVER EXCEED 90 - 100ºC</p><p>　　5. Vi

77、bra-house oil quantity and quality must be correct (See more on chapter 12.1)</p><p>　　6. The first oil-change must take place no later than after 20 hours.</p><p>　　4. BASIC INSPECTION BEFORE O

78、PERATION</p><p>　　4.1 Check the oil level</p><p>　　Level the Movax using the angle sensors (Movax x = 0 Movax y = 0)</p><p>　　The oil level must be between the first quarter from bo

79、ttom and bottom in the oil sight glass (see pictures 7,8). Using more oil than recommended, will decrease the performance of your Movax</p><p>　　Picture 8 (too high oil level,May cause overheating ! )</

80、p><p>　　SPH 80 see page 24 for location of oil sight glass</p><p>　　4.2 Check for cracks and leaks</p><p>　　Ensure that maintenance service is done. (oil change, lubrication)</p>

81、<p>　　Check for any leaks or damage to the hoses.</p><p>　　Check the grip pads. They must have more than 50% of teeth left (see chapter 12.4) </p><p>　　Check carefully all welded seams /

82、steel plates for cracks </p><p>　　ALL CRACKS MUST BE REPAIRED BEFORE ANY USE OF MOVAX!</p><p>　　Check and tighten loose bolts and hydraulic fittings</p><p>　　Note! Always clean the

83、 bolts and hydraulic fittings carefully and use locking glue before tightening the bolts.</p><p>　　Check the electric wires (cables) and connectors for any damage.</p><p>　　Check visually the ab

84、sorbing rubbers.</p><p>　　4.3 Check the tankline</p><p>　　Make sure that the pressure and tank hoses (in SPH 80 also the leak line) are in correct order. If the excavator’s pipeline for separat

85、e devices has on / off valves or a separate tap, BE ABSOLUTELY SURE, THAT THE TANK LINE IS OPEN! USING MOVAX WHILE TANK LINE IS CLOSED WILL CAUSE SERIOUS DAMAGES TO THE HYDRAULIC SYSTEM ESPECIALLY THE MOTORS.</p>

86、<p>　　Drive out the air from the hydraulic system after changing hoses or other items that introduce air into the system. It is done by vibrating for 10 – 15 seconds. Note! Vibrating does not purge the air out

87、from the cylinders and rotation hoses (see chapter 8). Before gripping a pile check all movements carefully.</p><p>　　4.4. Check the oil-flow and pressure of the excavator</p><p>　　Check the oi

88、l-flow and pressure every 750 – 1000 hours. (See page 22.)</p><p>　　When driving into soft ground, use lower RPM of the excavator’s engine, but make always sure that the Movax vibra-motor is running smoothly

89、. (Do not let the vibra-motor to resonate).</p><p>　　When driving into hard ground, use higher RPM and thus higher oil-flow. Make sure that the vibra-motor is running smoothly. However, never run Movax at to

90、o high Vibra RPM.</p><p>　　Note: 30 % lower oil-flow can lead to severe resonation, which in turn can lead to:</p><p>　　Increased bearing temperature</p><p>　　Bearing failure</p&

91、gt;<p>　　Vibra-shaft breakdown</p><p>　　5. LIFTING A PILE INTO VERTICAL POSITION</p><p>　　A) Before gripping a pile with the jaws, check that the pile and Movax are parallel (see picture

92、 9).</p><p>　　B) Before lifting, make sure that the jaws are inside the pile (see picture 10).</p><p>　　C) Push the "close jaws" button for 2 - 3 seconds to ensure that the max jaw f

93、orce is applied.</p><p>　　D) Lift the pile a little from the ground (see picture 11)</p><p>　　Picture 9 Picture 10 Picture 11 </p><p>　　Pil