等臂杠桿夾具設計

1、0目錄引言第1章等臂杠桿加工工藝規程設設計等臂杠桿加工工藝規程設設計...........................................................11.1零件分析零件分析...............................................................................................................11.1

2、.1零件的作用.................................................................................................................11.1.2等臂杠桿的主要加工表面及技術要求...............................................................11.2工藝規程的設計工藝規程

3、的設計..............................................................................................................11.2.1確定毛坯的制造形式............................................................................................

4、....11.2.2等臂杠桿機械加工定位基準的選擇..................................................................21.2.3等臂杠桿的機械加工工藝過程.............................................................................2第2章等臂杠桿加工等臂杠桿加工2510mmmm??、孔夾具設計孔

5、夾具設計.......................................42.1加工加工2510mmmm??、孔夾具設計孔夾具設計..............................................................................42.1.2定位誤差分析..........................................................

6、................................................42.1.3切削參數和機動時間的計算與夾緊力分析......................................................52.2鉆套、襯套、鉆模板及夾具體設計鉆套、襯套、鉆模板及夾具體設計............................................................

7、................92.2.1鉆套、襯套設計.........................................................................................................92.2.2鉆模板及夾具體設計.......................................................................

8、.......................122.3夾具精度分析夾具精度分析...................................................................................................................122.4本章小結本章小結....................................................

9、........................................................................14結論結論..............................................................................................................................................

10、.15參考文獻參考文獻....................................................................................................................................16附件附件I機械加工工藝過程卡機械加工工藝過程卡....................................................

11、..................................17附件附件II機械加工工序卡片機械加工工序卡片..........................................................................................182第1章等臂杠桿加工工藝規程設計等臂杠桿加工工藝規程設計1.1零件分析零件分析1.1.1零件的作用零件的作用題目給出的零件是杠桿。它的主要的

12、作用是用來支承、固定的，要求零件的配合要符合要求。1.1.2等臂杠桿的主要加工表面及技術要求等臂杠桿的主要加工表面及技術要求如圖11所示，等臂杠桿的主要加工表面有：圓兩端面、凸臺40mm?30mm?表面、、、孔等，主要技術要求為：25mm?10mm?8mm?1.由圓及30mm寬凸臺組成的上端面表面粗糙度為40mm?6.3aRm?外圓下端面表面粗糙度為，兩平面位置為。40mm?3.2aRm?00.04654mm?2兩個凸臺表面粗糙度為，與

13、外圓下端面位置分30mm?6.3aRm?40mm?別為、，兩凸臺厚為15mm。0.1204mm?0.3058mm?3.孔尺寸為，表面粗糙度為，并且后續各25mm?0.052025mm??1.6aRm?孔對其軸線將有位置和平行度要求，即都以其為設計基準。4.孔尺寸為，表面粗糙度為，與其軸線與10mm?0.015010mm??3.2aRm?孔軸線的平行度為。25mm?0.1mm5.兩個孔尺寸為，孔軸線與孔軸線距8mm?0.01508mm??