i_思科無線控制器配置基礎(chǔ)

1、思科無線控制器配置基礎(chǔ),Controller Initial Setup Options,Serial Console PortAvailable on all modelsMale DB-9 pin connectorSupports pins 2,3&5Default port configuration9600 baud8 data bits1 stop bitNo parityNo hardware

2、flow controlDB-9 female to female null-modem serial cableDedicated to AireOS managementEnsures access to AireOS in the event of a network failureCan be used for initial installationAccess to CLI only,Service Interfa

3、ce PortNot available on all modelsOnly on 4XXX series10/100Base-TX Ethernet port which is speed auto-sensingService Interface Port is not auto-sensing for DTE / DCEStraight-through ethernet cable to controller or hu

4、b Crossover ethernet cable to end station or routerCategory 5 Ethernet cableDedicated to AireOS managementEnsures access to AireOS in the event of a network failureCan be used for initial configuration or OOB manage

5、ment from management networkHas a default 192.168.1.1/24 default IP address,Boot Options,The controller boot sequence will always have these option available since this is set in PROM to ensure controller recovery optio

6、ns,,Run Primary or Backup Image,If no escape key is hit to halt the boot process and to enter the boot options menu, the boot process will begin automatically,Cisco Airespace AireOS Version,Bootloader: Not found only aft

7、er initial controller boot or controller upgrade,,,Run Primary or Backup Image (continued),AP will not light up until Starting Power Over Ethernet Services: ok,Web Authentication Certificate not found (error) only after

8、initial controller boot or controller upgrade,Cisco Airespace Wizard Configuration Tool begins automatically if no saved configuration,,,,Controller Configuration,Single binary configuration fileImportant to perform con

9、figuration backupsNo text outputShow running configuration is a summary configuration not in command syntaxContains no MAC address informationCan be ported to multiple Cisco Airespace ControllersBeware of duplicate

10、IP addressesController has two configurationsRunning-configurationAny commands take effect immediately and are only part of the running-configuration until a save configuration command is issuedIf not saved, commands

11、 will be lost in the case of a reset without a save configuration or a power cycleSaved-configurationConfiguration saved in NVRAM after performing save configuration command,CLI Wizard Configuration Tool,CLI Wizard Con

12、figuration Tool (continued),Command Line Interface (CLI)Basic Command Set,Command Line Interface (CLI) “clear” Commands,Command Line Interface (CLI) “config” Commands,Command Line Interface (CLI) “config” Commands (c

13、ontinued),Command Line Interface (CLI) “debug” Command,Command Line Interface (CLI) “help” Commands,Command Line Interface (CLI) “show” Commands,Command Line Interface (CLI) “show” Commands (continued),,Command Line

14、Interface (CLI) “transfer” Commands,Menu Bar,,MONITOR Provides a view of this controller, its APs and wireless clients,,,,WLANs Provides WLAN configurations such as SSIDs and security policies for all user groups,CONTR

15、OLLER Provides controller wide configurations such as Layer 2/3 mode, Multicast and mobility settings,WIRELESSProvides AP configurations, clients management and various RF settings,Menu Bar (continued),,,,SECURITY Pro

16、vides integration into security structure such RADIUS connectivity,MANAGEMENT Provides integration into the network such as IP addressing and SNMP,COMMANDSProvides administrative options such as upgrades and backups,A

17、dministrative Commands,,,Switch web interface will refresh every five minutes but when looking at statistics, it is recommended to observe the latest information which can be provided by clicking Refresh,,Context Sensiti

18、ve Help,Management > Local Management Users,Local Management Users accounts are used by both CLI and switch web interface,Management > HTTP,After Switch Web configuration wizard saves the configuration and reboots

19、the controller, HTTPS access will be enabled and it uses PKI to secure the transaction while HTTP access will be disabled by default,,Management > Mgmt via Wireless,,Cisco Airespace Controller can be managed via WLAN

20、clients but this capability is disabled by default,Management > Telnet-SSH,Cisco Airespace Controller supports both Telnet & SSH but SSH is enabled by default to secure the transactions,Management > Serial Port

21、,Serial port timeout and data rate can be managed from switch web interface,Management > User Sessions,Cisco Airespace Controller can also be managed via CLI and monitored from switch web interface,Controller > Gen