家用電風扇葉片注塑模具設計畢業設計

1、杭州電子科技大學本科畢業設計I摘要本論文闡述一套用于生產風扇葉片的注塑模具設計，給定參數：風扇直徑30CM，風扇功率45W來進行設計。設計時首先設計出塑件模型，然后選擇合適的材料，接下來再進行模具設計（此次設計應用ProE野火4.0版設計）。包括設計模具的成型系統、澆注系統、冷卻系統、導向系統、脫模系統等。設計的重點在于成型系統和澆注系統與脫模系統，而成型系統的重點在于分型面的設計，它決定了型芯和型腔結構以及模具的質量。因?yàn)樯热~塑件比較

2、特殊，葉片的厚度較薄，所以澆注系統澆口和主分流道的選擇顯得尤為重要。在設計中通過合理設計推出機構和脫模機構，保證了扇葉脫模時受力均勻，避免了葉片變形、扭曲。最后，通過選用合適的標準模架，設計出一套完整的模具。此外為保證設計合理，對注塑件進行各種工藝仿真，提高了模具的設計效率！關鍵詞關鍵詞：風扇葉片；注塑模具；ProE設計；分型面；成型系統；澆注系統杭州電子科技大學本科畢業設計III目錄第一章前言.....................

3、................................................................................................11.1研究的意義..........................................................................................................11.2國內外研究

4、動態..................................................................................................11.3設計的任務和要求..............................................................................................3第二章風扇造型和材料選擇.

5、........................................................................................42.1風扇造型..............................................................................................................42.2材料選擇......

6、........................................................................................................5第三章工藝分析............................................................................................................

7、.63.1總體分析..............................................................................................................63.2拔模檢測.............................................................................................

8、.................63.3厚度檢測..............................................................................................................73.4澆口分析.............................................................................

9、.................................73.5注射機選擇..........................................................................................................8第四章成型系統設計..............................................................

10、.....................................104.1裝配參照模型....................................................................................................104.2設置收縮率..............................................................

11、..........................................104.3創建工件............................................................................................................114.4創建分型曲面..................................................

12、..................................................114.5創建模具體積快................................................................................................114.6拉桿設計.....................................................

13、.......................................................12第五章澆注系統設計...................................................................................................135.1主流道設計.............................................

14、...........................................................135.2分流道設計........................................................................................................145.3澆口設計......................................

15、......................................................................155.4冷料穴設計........................................................................................................16第六章冷卻系統設計.........................

16、..........................................................................17第七章合模導向機構設計...........................................................................................187.1導柱的設計................................

17、........................................................................187.2導柱的布置........................................................................................................197.3導套的設計........................

18、................................................................................197.4導柱與導套的配合............................................................................................20第八章推出機構設計........................

19、...........................................................................218.1設計原則............................................................................................................218.2推出力的計算.................

20、...................................................................................218.3推桿設計...........................................................................................................228.4復位桿設計...........

21、.............................................................................................228.5推出機構導向系統設計....................................................................................22第九章其他輔助件設計................