hismelt熔融還原技術

1、HIsmelt熔融還原技術Smelt Reduction Technology - HIsmelt 匯報人：賈利軍Presentor: Jia Lijun,,匯報內容Content,1 HIsmelt技術簡介HIsmelt introduction2 HIsmelt工藝技術優勢Technical advantage of HIsmelt3 生產情況介紹Plant operation experience4 工藝流

2、程的優化Optimization of process5 結論 Conclusion,1.1 引言 Background,HIsmelt煉鐵工藝是已實現工業化生產的熔融還原煉鐵技術之一，屬于當今冶金領域前沿技術，經過三十多年的研究開發和生產實踐，工藝技術逐漸成熟。 As one of the commercialized smelt reduction iron-making technology, HIsm

3、elt has evolved to a mature solution after thirty years of research and development. HIsmelt煉鐵工藝技術是利用非焦煤及鐵礦粉采取噴射方式生產液態鐵，是解決我國焦煤資源貧乏和環保問題的先進煉鐵技術。 HIsmelt uses non-coking coal and iron ore fines, which off

4、ers a solution to the coking coal scarcity and environmental problem in China. HIsmelt煉鐵工藝在澳大利亞奎那那工廠從2005年至2008年已有3年的生產實踐。由于HIsmelt技術上的優勢，吸引了全球鋼鐵行業的目光，受世界金融危機影響，HIsmelt奎那那示范廠2008年年底停產，且不再復產。HIsmelt Kwinana pla

5、nt in Australia had run fours years from 2005 to 2008 and it successfully demonstrated the advantage of this technology . It was forced to shut down due to global economic crisis. 國內某公司自2004年以來一直致力于新煉鐵工藝、技術、裝備的

6、研究，在2012年決定利用部分HIsmelt奎那那工廠設備，并通過進一步優化工藝流程，建設新的HIsmelt熔融還原煉鐵生產廠。 A Chinese company , who has been focusing on the research of innovative iron-making technology, process and equipment, decided to build a HIsmelt plan

7、t in China. This plant uses some of the Kwinana equipment, but also makes some modification by optimizing the existing process.,1.2 HIsmelt工藝描述 HIsmelt Process Description,煤氣室,煙道,上部燃燒區,渣口,水冷板,噴泉及渣層,殘鐵口,熱風噴槍,水冷板,天然氣噴槍（

8、或煤槍）,固體噴槍,帶內襯前置爐,帶內襯的前置爐通道,帶內襯的爐底,鐵水熔池,渣區冷卻器,煤中碳素溶于鐵水, 礦石溶于渣中 carbon in the coal dissolve in the bath, 含鐵原料被還原成液態鐵水； Iron-bearing material is reduced to liquid iron 脈石和灰份被從礦石和煤中分離形成爐渣； gang and ash from ore a

9、nd coal form slag工藝反應產生的煤氣與熱風進行二次燃燒產生熱能； process gas combust with hot blast to produce energy渣與鐵水液體把能量帶入熔池以維持反應。 metal and slag droplet bring part of the energy back to the bath to sustain the reaction,,,,,SRV

10、 熔融還原爐中發生的反應為：Reaction in the SRV:,,1.3 HIsmelt工藝流程 HIsmelt process flow,Iron ore,dolomite,dryer,Pre-reduction kiln,Cyclone,Bag house,Dust injection,Coal mill,Coal,lime,Granulated slag,Coal mill,Ore injection,coal inje

11、ction,limel injection,Iron recovery,Slag granulation,Ladle car,Steel mill,Pig caster,Knock out vessel,Convective cooler,Waste gas,FGD,Cyclone de-dusting,Stoves,boiler,FGD,Suck fan,Oxygen plant,Electrical blower,scrubber,

12、Hot gas generator for the coal mill,Generator,HIsmelt工藝技術優勢 Advantages of HIsmelt,投資成本低：與傳統的煉鐵技術相比，Lower capital cost compared with traditional blast furnace due to: HIsmelt不需要焦?fàn)t和燒結廠或球團廠，因此建設成本降低； HIsmelt eliminates

13、 coke oven, sinter plant and pellet plant HIsmelt 工藝中的許多設備和設施，如熱風爐、噴煤系統、發電等都是高爐煉鐵工藝常用的設施，因此工廠建設相對比較簡單， HIsmelt shares many common equipment used in blast furnace, such as hot blast stoves, generator etc. HIsmelt技術所使

14、用的原料比較靈活，因此無需大型原料混勻場，極大降低了HIsmelt工廠的占地面積。 HIsmelt is flexible in raw materials selection and no blending facility is needed.,2 HIsmelt工藝技術優勢 Advantages of HIsmelt,操作成本低：Lower operational cost直接使用礦粉和煤粉作為原燃料煉鐵，不用

15、焦炭、球團和燒結。HIsmelt uses iron ore fines and coal directly; no coke, sinter or pellet will be needed.,更大的原料靈活性Great flexibility in raw material：HIsmelt技術可直接噴吹傳統高爐燒結廠不宜使用的低品位鐵礦粉。 HIsmelt can use low grade iron ore fine

16、s which otherwise can not be used by the blast furnace sinter plant.,鐵水質量穩定，磷含量很低，基本不含硅，因此可進行少渣煉鋼，降低煉鋼成本。 Stable hot metal quality, low P content, almost no silicon; so less slag is needed in the steel mill and thus red

17、ucing steel mill cost,Himselt工藝與高爐生產鐵水成分對比HIsmelt Hot Metal vs. BF Hot Metal,鐵水質量好 Superior hot metal quality,降低環境影響，通過變革性的工藝創新，取消焦?fàn)t、燒結，HIsmelt極大的降低了SO2和NOx、基本遏制二惡英、焦油和酚的排放。Almost no emission of dioxins, phenols or ta

18、rs due to the revolutionary process and elimination of coking oven and sintering process.,更綠色環保的煉鐵技術 Less Environmental Impact,3 生產情況介紹 Production Experience,3.1 奎納納情況概覽 Kwinana summary 從2005年11月開始了為期3年的達產運行：2006年

19、底實現50%，2007年實現80%，2008年實現85%three year ramp-up period beginning in November 2005: 50% by 2006, 80% by 2007, 85% by 2008期間主要問題大多由外圍設備引起，在這些問題得以解決后生產率逐步上升。Major problems caused by ancillary equipment and production rat

20、e continued to rise as bottlenecks removed 2008年12月，由于經濟危機影響，生鐵市場低迷，工廠因此關閉。Plant put under care and maintenance and then closed due to sluggish market demand caused by global economic crisis from end of 2008,3.2 HI

21、smelt的生產情況 Production Data of HIsmelt,由上圖中可知，2008年12月日產最大達到1834t。Daily production reaches a maximum of 1834t in December of 2008.,3.2 HIsmelt的煤耗 Coal Rate of HIsmelt,4 工藝流程的優化 Process Modification,基于奎納納工廠的經驗，山東省冶金設計

22、院、力拓公司和業主決定對部分工藝流程和設備進行改進，以降低成本和浪費。 Based on the Kwinana experience, SDM, Rio Tinto and the end user decided to modify some of the process and equipment to reduce cost and waste.,4.1 新礦粉預熱系統 Modification of the Ir

23、on Ore Preheating,為降低工程投資，礦粉預熱采用了技術可靠的雙回轉窯工藝 A double kiln system is used which help reduce capital cost,特點 Advantage:改進后的工藝既能實現礦粉的加熱、預還原的目的，且技術成熟、設備運行穩定、作業率高。The kiln system is capable of preheating and pre-

24、reducing the iron ore. It is a mature, stable and efficient solution. 同時，改進后的預熱還原系統既可以采用煤粉也可以采用SRV煤氣作為燃料，設計獨立的煤粉供應系統，有助于提高HIsmelt工藝整體的作業率。At the same time, this system can run on both coal and SRV offgas, which help i

25、ncrease the utilization rate.,4.2 礦粉噴吹系統Modification of Iron Ore Injection System,考慮新的礦粉預熱系統的收塵系統收集的粉塵中含有大量的含鐵氧化物及少量未然碳粉，為提高資源的利用率，新的HIsmelt工藝設計中增加一套細粉噴吹系統，其主要作用：將工廠產生的含鐵、含碳粉塵噴入SRV內，完成含鐵廢棄物的合理利用，提高鐵水產量，同時噴入SRV內的含碳粉塵可以為

26、鐵礦石的融化還原提供熱源和還原劑，有利于降低噸鐵工序能耗。The new HIsmelt plant added a dust injection system to recover the iron bearing dust and carbon bearing dust, which will help reduce waste and improve raw material utilization rate.,4.3 鐵

27、、渣系統的改進Modification of the slag and metal handling system,殘鐵回收：當SRV事故狀態時，一次殘鐵量約300t鐵水需從SRV爐內排出，因此新設計中通過增加殘鐵回收跨，殘鐵回收跨內設置有殘鐵受鐵設施，設置有通向鑄鐵廠房的80t鐵水罐電動平車，使SRV爐殘鐵能至鑄鐵機鑄鐵，有利于殘鐵的再利用。End tapped metal recovery: about 300t hot met

28、al will be discharged to the pit if there is an emergency. A end tap metal recovery facility is designed and 80t ladle cars are used to transfer the end tap metal to the pig caster.,熔渣處理及渣中鐵的回收技術 Slag handling and ir

29、on recovery,該流程能有效回收HIsmelt熔融還原技術生產熔渣中攜帶的鐵，能提高HIsmelt工藝鐵水收得率，降低HIsmelt工藝的工序成本。This process helps recover the iron trapped in the slag during slag tapping, thus reducing the production cost.,圖中：1—熔渣溝；2—渣罐；2’—渣罐；3—專用起重機；4

30、—渣罐運輸車；5—渣罐傾翻裝置；6—熔渣溝；7—熔渣處理設施；8—鐵水罐運輸車；9—鐵水罐；,HIsmelt熔融還原工藝熔渣中鐵的回收流程如下圖The following is the process of recovering the iron trapped in the slag:,4.4 煤氣余熱回收系統 Modification of offgas waste heat recovery system,去除煤

31、氣中攜帶的較大顆粒煙塵，防止后續煤氣管道積灰堵塞。Remove the large particles in the dust and avoid blocking the offgas pipes,降低氣體的含塵量，提高氣體的對流換熱系數。Reduce dust content and increase heat exchange efficiency,回收余熱，產生蒸汽用于發電；Waste heat is recovered to

32、generate electricity,當余熱鍋爐故障時，高溫氣體可以直接進入濕法洗滌系統，不影響SRV正常生產。When the boils stops, hot offgas will goes to scrubber.,4.5 鍋爐及動力系統 Modification of the Boiler and Power system,原鼓風發電機組利舊 Old TAB will be re-used新增一臺中

33、溫中壓抽汽凝汽式汽輪發電機組。 Add a new medium pressure turbine generator增設一臺電動鼓風機備用。 Add a back up electrical blower制氧驅動方式改為電動。 Oxygen plant is driven by electricity燃?xì)忮仩t采用自然循環，在爐膛下部采用強化傳熱傳質的SRV煤氣鍋爐爐內蓄熱穩燃裝置，保證了難以燃燒的SRV煤氣的充分

34、燃燒。 The boiler uses natural circulation. There is a thermal storage device in the lower chamber of the boiler which help stabilize combustion.,特點：各系統相互獨立，互不影響。 Characteristic: the function of each equipment is not s

35、olely reliant on the upstream equipment, which provides redundancy.,5 總 結 Conclusion,Hlsmelt熔融還原煉鐵技術是實現工業化生產的非高爐煉鐵技術之一，其工藝可看作是冶金行業中各種成熟技術的新組合，和當前的耐火材料技術、噴吹技術、煙氣余熱回收和凈化技術以及其他的冶金技術的發展是相輔相成的，是高爐最有力的競爭者, 是有希望革高爐命的新技術。

36、 HIsmelt is one of the commercialized non-BF technologies. HIsmelt consists of many common and mature technologies, such as refractory, injection, waste heat recovery and scrubbing. It is regarded as the most competent

37、competitor of blast furnaces.,在HIsmelt工藝國產化過程中吸取奎那那工廠的生產經驗，對原有工藝進行了優化完善，新的工藝既改善了工藝的穩定性，提高系統的作業率，又采取了有效節能降耗、資源合理利用措施，有效降低噸鐵工序能耗，為提升HIsmelt的競爭力提供了強有力的技術保障。Based on Kwinana’s experience, the Chinese plant modified the old

38、process and equipment. It is expected that the new process is more stable and energy-efficient, therefore more competent.,祝愿HIsmelt技術為煉鐵節能環保做出偉大貢獻Wish HIsmelt achieves more in terms of energy efficiency and environment